铝合金滚压复合机较低报价 济南诺托数控复合机

铝合金滚压复合机较低报价，济南诺托数控复合机

 

 

齿是通过安装在开齿机上的硬质滚齿轮在铝型材用于穿条的槽口颈部滚出齿来，是特别关键的一道工序。

 

滚齿轮通过传输机构由电机驱动而产生转动，滚齿轮外缘的60度形状的齿压在铝材槽口中点并施加一定压

 

力，带动铝材向前移动，同时在压过的槽口外沿滚出齿来。滚齿轮通过导轨能上下左右调节，以适应不同

 

高度和宽度的型材 

Hobbing is by installing in hard rolling gear hobbing machine in the aluminum used to slit 

 

neck wear of the roll out teeth, is a process with the special key. Roller gear and driven 

 

by a motor through a transmission mechanism, 60 degrees shape of the outside of the roller 

 

gear tooth pressure in the middle of the aluminum slot and a certain pressure, led aluminum 

 

moving forward, at the same time outside the pressure of rabbet along the tooth to get out 

 

of. Rolling gear through the guide to the up and down or so control, in order to adapt to 

 

different height and width of the profile 

Open tooth wear all-in-one 

齿应开在槽口的外锤头侧，在内锤头尽可能不开齿或只开很浅的一点齿。原因是在后面的滚压工序中，外

 

锤头会产生以自己颈根部为圆心的旋转变形而将开好的齿压入隔热条，从而保证滚压后隔热铝材的剪切强

 

度。而槽口的内侧为定位部位，用来保证滚压后隔热型材的整体形状尺寸，就算内侧的齿开的很好，滚压

 

后也压不到隔热条里，因此没有任何效果 

Teeth should be open on the hammer head outside the side of the slot, hammer head, as far as 

 

possible, dont open or open only shallow tooth. Reason is that in the back of the rolling 

 

process, the hammer head will produce deformation of the rotation of the centered on his 

 

neck roots and will have a good tooth pressure into the insulation, so as to ensure the 

 

shear strength of insulating aluminum after rolling. And the inner side of the slot for 

 

locating part, which is used to ensure the overall shape of insulating material after 

 

rolling size, even if the inside of the gear drive is very good, also after rolling pressure 

 

is less than heat insulation in the article, so there is no any effect 

好齿形的齿峰应小于0.2mm,不超过齿距的三分之一左右，这样滚压时才容易压入隔热条内。如果开齿太钝

 

或没有开齿，就难以压入隔热条，隔热型材的剪切性能就无法保证。开齿的好坏主要由开齿轮质量、机器

 

设备稳定性和操作水平来决定的。 

Good tooth shape of the teeth should be less than 0.2 mm, less than a third of the pitch, so 

 

when rolling pressure easily into the insulation within the article. If the tooth is too 

 

dull or no teeth, it will be difficult to press into the heat insulation, heat insulation 

 

material shear performance will not be able to guarantee. The stand or fall of hobbing is 

 

mainly composed of drive gear, machinery and equipment, quality stability and operation 

 

level. 

开齿轮外缘的齿形斜面应左右不对称，外侧角度应大些，这样方便将齿开在铝材槽口外侧。开齿穿条一体

 

机开齿轮是损耗件，时间一长外缘的齿就会逐渐磨损，一般建议120吨左右要变新的开齿轮，当然这要看

 

开齿盘的材质，差一些的几十吨就要更换，好一些的进口轮能使用更长的时间。开齿穿条一体机好的设备

 

因稳定性好，往往更容易保证开齿的质量，若设备的稳定性欠佳，就会造成开齿盘的跳动，使得同一支型

 

材一段开齿好，一段开齿不好，影响整体的开齿质量